Knowledge & Tips
Air Compressor Maintenance Tips and Operation Instructions Well Explained
Jul
How to maintain air compressors? What should we pay attention to when operating air compressors? Here let Chengdu Pudding Mechatronic Co. (CPMC) provide the advices on air compressors maintenance and instructions on how to operate the system.
Air Compressors Maintenance Tips – 4 Main Sectors
1. Replace the air filter;
2. Replace the oil filter;
3. Replace the oil and gas separator;
4. Replace lubricating oil;
Specific Air Compressors Operation Methods
The following operations must be performed only when the power is turned off and there is no pressure in the machine)
1. Replace the air filter
Remove the screw at the end of the air filter cover, remove the tail of the cover, remove the air filter locking screw, take out the air filter, install the new filter, and reinstall the filter and cover in the reverse steps.
2. Replace the oil filter
Use a special tool to lock the bottom of the filter and turn it forward to unscrew the filter. Use a clean cloth to clean the bottom of the filter and apply a little oil. Apply a little oil to the seal ring of the new oil filter and install the new filter. And lock it with special tools.
3. Replace The Compressor Air/Oil Filter
The method is the same as replacing the oil filter.
4. Replace lubricating oil
When the oil temperature is between 30 and 60℃, the viscosity will decrease and it will not burn your hands. At the same time, it will drain the residual oil of the unit. Therefore, if the oil is cold when changing the oil, first turn it on and run it for 2-3 minutes. When changing the oil, make sure that the unit is pressure-free before proceeding. First, disassemble the oil filling nut of the oil-gas separation barrel and prepare the residual oil with a suitable container. Open the oil drain valve under the barrel, and turn the head pulley by hand from time to time to drain the oil stored in the head.
After the oil is completely drained, close the drain valve. Inject new lubricating oil, and turn the head pulley by hand from time to time to facilitate the suction of oil into the pipe and the machine head. After immersing the oil level mirror, the oil fills 2~3cm (this is an empirical value, the actual oil level needs to be observed when the machine is turned on and loaded). After filling the oil, install and lock the oil nut, and remove the air intake Valve, inject a small amount of lubricating oil from the air inlet of the machine head, and the amount of oil is only two-thirds of the submerged rotor. Install the air inlet valve. Clean the surface of all parts of Henan air compressor.
Three, test machine
After power-on, directly start the air compressor, listen to whether there is any abnormal noise, observe whether there is oil leakage, and see whether the oil level is appropriate (the oil level should be observed during loading, and the position should be 1/ of the oil level mirror. 2~2/3) Otherwise, put more and less make up. After confirming that there is no abnormality, install the side panel and the rear side panel, and you are done.
Air Compressors Trade (Chengdu Pudding Mechatronic Co. Company Ltd)
Air Compressors Trade Service is online distributor for air compressors and compressed air products in Chengdu, southwest China. Not like most machinery distributors, our mission is not to sell as many air compressors or spare parts as we can. Our philosophy is to partner with more and more clients to help them salvage net profit by lowering their import cost. As is known to all that China is one of the HUGE manufature centers of the world. Every year tens of thousands of air compressors and compressors related parts go abroad from China. But due to the information gap and the lack of professionalism in air compressors services, most of the international buyers feel it is hard to find a reliable supplier with professional service and the most competitive prices. CPMC is growing to be China’s large online distributor offering BETTER prices than any of those compressors agents on Alibaba or Made-in-China because of the expensive commission, advertisement cost and transaction fee which is aggressively or outrageously charged by those platforms due to their namely high traffic. However our own networks enable us to provide the best prices and products to our customers. Learn more about Chengdu Air Compressors Dealer.
Dear Sir!
Please take a look and help us with your suggestions.
A5E01237899
A-Nr: 119977/09
Looking forward to hearing from you soon.
Nice day to you.
Hello Mr Finn
thanks for leaving message on our website. Lets stay in touch by email.Regards
Tony
kaeser compressor repair kit 400707.0
Thank you Mohammed for leaving the message, well currently Kaeser compressors parts are still restricted for distribution and we welcome your RFQs on other main compressors brands such as Atlas Copco, Sullair, INGERSOLL RAND (IR, CompAir, Doosan, Gardner Denver, etc). Thank you again.
Modern centrifugal compressors are equipped with sophisticated control systems that allow for precise regulation of air pressure and flow. These systems enable adaptive performance based on real-time demand, further improving efficiency and performance.
I’m Albert Arhin i need this part #37190111189 filter housing complete, please give me the price and the pictures.
Hello Albert, Thanks for leaving message on Epiroc spare parts, we have checked and this part number is not correct, however the correct part number can not be booked as well for this item. We welcome your other RFQs by email to info@aircompressorstrade.com.
Dear :sir/madam
I hope this email finds you well.
I am Eng. Ali yousee representing Power Tech for Engineering & construction.
We are interested in establishing a business partnership with your company to fulfill the requirements
We would like to get a quote for 4 complete units of air compressor and dryers with control systems according to following details:
– Atlas copco air compressor screw oil injected Model:GA132-7.5 bar, 4 units
-Atlas copco air compressor screw oil injected Model:GA110-7.5 bar ,4units
– Atlas copco twin tower heatless adsorption dryer Model:CD480+ / 4 units
– Atlas copco twin tower heatless adsorption dryer Model:CD400+ , 4units
– Atlas copco Equalizer pro.4 (EQ) control system up to 4 compressors
– others Accessories for installation
Best regards
Ali Yousee
Power Tech for Engineering and construction
Yemen,sanaa Almatar street
Tel:+96707873010
P.o.box:35059
Phon : +967777605085
Whatsup:+967737378715
Email: info@uptech.com.ye/info@hyzpower-s.com.ye
Thanks Ali for your message on our website, we well received and our team should have quoted to you via email. We welcome your RFQs and orders. Looking forward to supporting your business with our strong supply chain worldwide. Tony, funder of CPMC!
I want to buy several Sandvik parts, I currently buy from Türkiye and would like more reliable suppliers
Thank you for your message RFQ on our website, we welcome your inquiries and orders on Sandvik, Epiroc drilling and mining equipment parts, and Atlas Copco, Ingersoll Rand, CompAir, Doosan, Gardner Denver, Sullair air compressors spare parts. Please always feel free to write an email to us when you have RFQs and orders demand. Thank you, Tony, funder of CPMC.